Beginners Guide: nse7 fortinet


♥♥ 2017 NEW RECOMMEND ♥♥

Free VCE & PDF File for Fortinet NSE7 Real Exam (Full Version!)

★ Pass on Your First TRY ★ 100% Money Back Guarantee ★ Realistic Practice Exam Questions

Free Instant Download NEW NSE7 Exam Dumps (PDF & VCE):
Available on: https://www.certleader.com/NSE7-dumps.html


NSE7 Product Description:
Exam Number/Code: NSE7 vce
Exam name: Fortinet Troubleshooting Professional
n questions with full explanations
Certification: Fortinet Certification
Last updated on Global synchronizing

Instant Access to Free VCE Files: Fortinet NSE7 Fortinet Troubleshooting Professional

NSE7 examcollection

Actualtests offers free demo for nse7 exam exam. "Fortinet Troubleshooting Professional", also known as nse7 exam exam, is a Fortinet Certification. This set of posts, Passing the Fortinet nse7 fortinet exam, will help you answer those questions. The fortinet nse7 Questions & Answers covers all the knowledge points of the real exam. 100% real Fortinet nse7 fortinet exams and revised by experts!

Q1. An administrator has enabled HA session synchronization in a HA cluster with two members. Which flag is added to a primary unit's session to indicate that it has been synchronized to the secondary unit? 

A. redir 

B. dirty 

C. synced 

D. nds 

Answer:


Q2. An LDAP user cannot authenticate against a FortiGate device. Examine the real time debug output shown in the exhibit when the user attempted the authentication; then answer thequestion below. 

Based on the output in the exhibit, what can cause this authentication problem? 

A. User student is not found in the LDAP server. 

B. User student is using a wrong password. 

C. The FortiGate has been configured with the wrongpassword for the LDAP administrator. 

D. The FortiGate has been configured with the wrong authentication schema. 

Answer:


Q3. Examine the following routing table and BGP configuration; then answer the question below. 

TheBGP connection is up, but the local peer is NOT advertisingthe prefix 192.168.1.0/24. Which configuration change will make the local peer advertise this prefix? 

A. Enable the redistribution of connected routers into BGP. 

B. Enable the redistribution of static routers into BGP. 

C. Disable the setting network-import-check. 

D. Enable the setting ebgp-multipath. 

Answer:


Q4. Examine the IPsec configuration shown in the exhibit; then answer the question below. 

An administrator wants to monitor the VPN byenable the IKE real time debug using these commands: 

diagnose vpn ike log-filter src-addr4 10.0.10.1 diagnose debug application ike -1 diagnose debug enable 

The VPN is currently up, there is no traffic crossing the tunnel and DPD packets are being interchanged between both Ipsec gateways. However, the IKE rea time debug does NOT show any output. Why isn't there any output? 

A. The IKE real time debug shows the phases 1 and 2 negotiations only. It does not show any more output once the tunnel is up. 

B. The log-filter setting is set incorrectly. The VPN's traffic does not match this filter. 

C. The IKF real time debug shows the phase 1 negotiation only. For information after that, the administrator must use the IPsec real time debug instead: diagnosedebug application ipsec -1 

D. The IKE real time debug shows error messages only. If it does not provide any output, it indicates that the tunnel is operating normally. 

Answer:


Q5. Examine the IPsec configuration shown in the exhibit; then answer the question below. 

An administrator wants to monitor the VPN byenable the IKE real time debug using these commands: 

diagnose vpn ike log-filter src-addr4 10.0.10.1 diagnose debug application ike -1 diagnose debug enable 

The VPN is currently up, there is no traffic crossing the tunnel and DPD packets are being interchanged between both Ipsec gateways. However, the IKE rea time debug does NOT show any output. Why isn't there any output? 

A. The IKE real time debug shows the phases 1 and 2 negotiations only. It does not show any more output once the tunnel is up. 

B. The log-filter setting is set incorrectly. The VPN's traffic does not match this filter. 

C. The IKF real time debug shows the phase 1 negotiation only. For information after that, the administrator must use the IPsec real time debug instead: diagnosedebug application ipsec -1 

D. The IKE real time debug shows error messages only. If it does not provide any output, it indicates that the tunnel is operating normally. 

Answer:


Q6. Examine the partial output from the IKE realtime debugshown in the exhibit; then answer the question below. 

Why didn't the tunnel come up? 

A. IKE mode configuration is not enabled in the remote IPsec gateway. 

B. The remote gateway's Phase-2 configuration does not match the local gateway's phase-2configuration. 

C. The remote gateway's Phase-1 configuration does not match the local gateway's phase-1 configuration. 

D. One IPsec gateway is using main mode, while the other IPsec gateway is using aggressive mode. 

Answer:


Q7. An administrator added the following Ipsec VPN to a FortiGate configuration: 

configvpn ipsec phasel -interface 

edit "RemoteSite" 

set type dynamic 

set interface "portl" 

set mode main 

set psksecret ENC LCVkCiK2E2PhVUzZe 

next 

end 

config vpn ipsec phase2-interface 

edit "RemoteSite" 

set phasel name "RemoteSite" 

set proposal 3des-sha256 

next 

end 

However, the phase 1 negotiation is failing. The administrator executed the IKF real time debug while attempting the Ipsec connection. The output is shown in the exhibit. 

What is causing the IPsec problem in the phase 1 ? 

A. The incoming IPsec connection is matching the wrong VPN configuration 

B. The phrase-1 mode must be changed to aggressive 

C. The pre-shared key is wrong 

D. NAT-T settings do not match 

Answer:


Q8. Examine the output of the 'diagnose sys session list expectation' command shown in the exhibit; then answer the question below. 

Which statement is true regarding the session in the exhibit? 

A. it was created by the FortiGate kernel to allow push updates from FortiGuard. 

B. it is for management traffic terminating at the FortiGate. 

C. it is for traffic originated from the FortiGate. 

D. it was created by a session helper or ALG. 

Answer:


Q9. Examine the output of the 'diagnose sys session list expectation' command shown in the exhibit; then answer the question below. 

Which statement is true regarding the session in the exhibit? 

A. it was created by the FortiGate kernel to allow push updates from FortiGuard. 

B. it is for management traffic terminating at the FortiGate. 

C. it is for traffic originated from the FortiGate. 

D. it was created by a session helper or ALG. 

Answer:


Q10. What configuration changes can reduce the memory utilization in a FortiGate? (Choose two.) 

A. Reduce the session time to live. 

B. Increase the TCP session timers. 

C. Increase the FortiGuard cache time to live. 

D. Reduce the maximum file size to inspect. 

Answer: A,D



To know more about the Fortinet Troubleshooting Professional, click here.